skip to Main Content

How to choose a grow light: spectrum, wattage and coverage

Ask in any grow shop which light to buy and you’ll usually get a wattage back. “Get a 200.” Fair enough, but watts are what the lamp eats, not what it gives your plants. Two 100 W lamps can land wildly different amounts of usable light on a canopy, and the one that looked like a bargain is often the one that costs more on the electricity bill.

What really counts comes down to three things. The colour of the light. How much of it actually reaches the leaves. And how many watts it burns to get there.

We make our own lights and measure them in our own lab, so rather than repeat the usual rules of thumb, we’ve put our figures on the table. Read to the end and you’ll know which spectrum to pick, how much power your tent needs, and which lines of a datasheet are worth your attention (most of them aren’t).

What a grow light actually does

Your eyes and your plants don’t see the same thing. Photosynthesis feeds on photons between roughly 400 and 700 nm, and the number that matters is how many of them hit a square metre of leaf each second. Growers call it PPFD, short for Photosynthetic Photon Flux Density, and it’s given in µmol/m²/s.

Some context helps. At 45° of latitude (picture a line through Bordeaux and Turin), the average daytime PPFD outdoors looks like this. London is further north, so knock a bit off:

Season Average daytime PPFD
Winter 170 µmol/m²/s
Spring 400 µmol/m²/s
Summer 750 µmol/m²/s

Think of an LED grow light as a way to pick one of those seasons and keep it going inside your tent, whatever the month.

Step 1: choose the spectrum

There are really only two families to choose from. Which one suits you depends on where your plants are in their life.

Spectrum What it imitates Best for
Grow spectrum (6500 K, cold white) spring sun, more blue than red cuttings, seedlings, leafy growth
Full spectrum (bloom) summer sun, more red than blue flowering and fruiting, and the whole cycle

Our full spectrum bars blend four kinds of LED. Warm white at 2700 K, neutral at 4000 K and cold at 6500 K make up 23% each, and the last 31% is deep red at 660 nm. Why keep cold white in a bloom light? Because young plants still want their blue, and with it in the mix a single full spectrum light can carry a crop all the way from seedling to harvest. Grow spectrum is more of a specialist. Brilliant for propagation, a bit short on red once flowers appear.

So, in practice: herbs, salads, microgreens, grow spectrum is plenty. Tomatoes, chillies, strawberries, anything that flowers? Go full spectrum.

What about UV and infrared?

Neither one feeds photosynthesis much. Used as extras, though, they earn their keep:

  • Near ultraviolet toughens the plant’s defences, helps keep mould away and shortens the internodes, which gives you stockier plants. Keep it to two hours a day at most, inside the normal lighting period, and put it on its own timer.
  • Near infrared warms the canopy, stretches the internodes and can nudge plants into flowering. This one can stay on for the whole lighting period.

Treat both as boosters. On their own they’re not a light source, full stop. Our Cosmorrow UV and IR boosters run off the same 24 V power supply as the main bars, so there’s no extra wiring to worry about.

Step 2: choose the light level

Right colour sorted, the next question is quantity. We class every one of our lights into one of three levels:

Level PPFD on the canopy Use
Level I 0 to 300 µmol/m²/s propagation, vegetative stage, early growth
Level II 300 to 600 µmol/m²/s growth
Level III over 600 µmol/m²/s intensive growth, flowering, fruiting

Get this wrong with seedlings and you’ll know quickly. Too much light bleaches the leaves; too little and the stems shoot up, thin and floppy, hunting for more. For a propagator or a seedling shelf, level I is the one. Fruiting plants in a tent are a different story, and they want level III.

How to read a PPFD map

Any manufacturer worth trusting publishes a PPFD map, meaning the light measured point by point over the whole grow area. Below is the one for our Power Pack 125 W full spectrum, taken at 30 cm above a 60 x 60 cm area (white board, 100% intensity):

820 925 1060 1060 925 820
925 1090 1230 1230 1090 925
1060 1230 1410 1410 1230 1060
1060 1230 1410 1410 1230 1060
925 1090 1230 1230 1090 925
820 925 1060 1060 925 820

Average: 1085 µmol/m²/s. Now skip the middle and look at the corners. Even there it reads 820, still comfortably level III, and that’s what people mean by even coverage. When a brand only quotes the peak under the centre of the lamp, ask yourself what’s going on at the edges of your tent.

One more habit worth having: check the distance and the area printed beside any PPFD figure. Without them the number is meaningless, since light spreads out and fades as the lamp goes up.

Step 3: work out how many watts you need

Watts only mean something once you know how efficient the light is. Keeping that in mind, this is the LED power we recommend for each of our tents, for level III growing with LEDs at 3.0 µmol/J:

Tent Floor area Advised LED power
Dark Street 60 (60 x 60 cm) 0.36 m² 100 W
Dark Street 90 (90 x 90 cm) 0.81 m² 200 W
Dark Street 120W (120 x 60 cm) 0.72 m² 200 W
Dark Street 120 (120 x 120 cm) 1.44 m² 400 W
Dark Room 150 (150 x 150 cm) 2.25 m² 600 W
Dark Room 240 (237 x 237 cm) 5.62 m² 1600 W
Dark Room 300 (297 x 297 cm) 8.82 m² 2400 W

Do the sums and you land around 250 to 280 W of efficient LED per square metre for intensive growing. Seedlings and cuttings need far less. On a Dark Propagator 90 (90 x 60 cm), for instance, we suggest 40 W per shelf for level I and 80 W for level II.

A less efficient light simply needs more watts to do the same job. Take a 100 W LED at 3.0 µmol/J: it gives out around 300 µmol of photons a second. A lamp at 2.0 µmol/J would need 150 W to match it. Which is why the next figure matters more than any other on the box.

Step 4: check the efficiency (PPE)

PPE, or Photosynthetic Photon Efficacy, tells you how many useful photons a light turns out for every watt it pulls from the wall. It’s measured in µmol/J, and frankly it’s the only fair way to line grow lights up against each other. Roughly, by technology:

Technology Typical PPE
Fluorescent: CFL, T5, T8 up to 1 µmol/J
Discharge lamps: HPS, MH, CMH up to 2 µmol/J
LED up to 3 µmol/J

Our Cosmorrow full spectrum bars sit at 2.85 µmol/J. Put plainly, for the same light you’d use about a third less electricity than with a discharge lamp, and two thirds less than with a compact fluorescent. The Power Pack goes a little further, to 3.01 µmol/J.

Is a T5 still worth buying, then? Over a shelf of seedlings, sure, it’ll do. In a tent it’s another matter: three times the power draw of a decent LED for the same light, plus the heat, and we struggle to see the case for it.

Step 5: match the format to the space

LED grow lights mostly come in two shapes, and the height and layout you’re working with will decide between them.

Bars and strips are slim and light, so they can sit very close to the plants. That’s exactly what you want on shelves, in propagators or in a kitchen grow station, where there might be only a few centimetres between the leaves and the shelf above. Our Cosmorrow LED bars run at 24 V, are waterproof (IP65) and rated for 50,000 hours. We test them at 15 to 20 cm:

Bar Spectrum PPE Measured over Average PPFD
COP2065, 20 W grow 2.70 µmol/J 60 x 40 cm at 15 cm 268 µmol/m²/s
COP20FS, 20 W full spectrum 2.85 µmol/J 60 x 40 cm at 15 cm 238 µmol/m²/s
COP4065, 40 W grow 2.70 µmol/J 120 x 60 cm at 15 cm 205 µmol/m²/s
COP40FS, 40 W full spectrum 2.85 µmol/J 90 x 60 cm at 20 cm 240 µmol/m²/s

A single bar puts you at level I, which is just right for a propagation shelf. Want level II? Add bars. And if you need to turn them down, they’ll dim to about 1 W with a PWM dimmer made for 24 V LED strips (do read the precautions in our FAQ first).

Panels pack more power into one fixture and hang higher, which suits a grow tent running at level III. The Power Pack 125 W covers 60 x 60 cm. Its big brother, the 250 W, covers 90 x 90 cm, where we measure an average of 960 µmol/m²/s at 45 cm. Both dim in 25% steps, and you can link and control them through their RJ12 ports.

Not keen on putting a setup together yourself? Our Grow Stations arrive with the lighting already fitted. The Original 60 has spring-like light for seedlings and microgreens; For Twenty 100 goes full spectrum for taller plants.

Step 6: set the lighting hours

PPFD is a snapshot, how strong the light is right now. Over a whole day, what the plant actually banks is the DLI (Daily Light Integral), in moles per square metre per day:

DLI = PPFD x hours of light x 0.0036

Here’s the neat bit. A level II light at 400 µmol/m²/s left on for 18 hours gives a DLI of 25.9. A level III light at 600 µmol/m²/s for 12 hours gives… 25.9 as well. A gentler light over long days can do the same work as a powerful one over short days.

As for hours, common practice is 16 to 18 a day for seedlings and leafy crops, and 12 for plants that flower when the days get shorter. Your crop may have its own preferences, so check.

Our checklist before you buy

  • Spectrum: grow spectrum for propagation and leafy crops, full spectrum once flowers and fruit are the goal.
  • Light level: level I for seedlings, level III for fruiting plants in a tent.
  • PPFD map: published, with distance and area stated, and still decent in the corners.
  • PPE: 2.7 µmol/J or better for an LED.
  • Real watts, not “equivalent” watts: count on roughly 250 to 280 W of efficient LED per m² for intensive growing.
  • Lifetime and protection: rated hours and IP rating, which matter a lot in a humid tent.

The whole range, with a datasheet for every model, is on our LED grow light page and in our technical data. We don’t sell online ourselves. Our lights go through specialist stockists in 37 countries, and you can find your nearest one on our stockist map.

Frequently asked questions

How many watts should your grow light be?

That depends on two things: the size of the area and how efficient the light is. With an LED at 3.0 µmol/J, allow about 100 W for a 60 x 60 cm tent, 200 W for 90 x 90 cm and 400 W for 120 x 120 cm if you’re growing intensively. A less efficient light will need more, so look at the PPE as well as the watts.

What color of LED is best for plant growth?

Plants use the whole visible spectrum. Blue drives leafy growth, red drives flowering and fruiting. Cold white at around 6500 K is a good match for seedlings and leafy crops, while full spectrum (warm and cold white plus deep red at 660 nm) handles the whole cycle.

Can any LED light be used as a grow light?

A household LED does give off light your plants can use, just nowhere near enough to stand in for the sun. It’s made for human eyes, not photosynthesis, and you won’t find a PPFD or PPE on the packaging. A grow light, by contrast, is built to put a known amount of useful light onto a given area.

Are cheap grow lights any good?

Some are, honestly. Price just isn’t much of a guide. See whether the light comes with a PPFD map at a stated distance, a PPE figure and a real wattage. Without those you can’t compare it with anything, and poor efficiency adds up over the 30,000 to 50,000 hours a good LED is rated for.

How many hours a day should you use a grow light?

It’s more useful to think in daily light than in hours. DLI is PPFD times hours of light times 0.0036, so a weaker light needs longer days to keep up. Common practice is 16 to 18 hours for seedlings and leafy crops, and 12 for plants that flower as the days shorten.

Back To Top
×Close search
Search